Various error messages when starting OS
- Document ID: 94000384
- Posted Date: 1996-08-19
- Last Updated: 1996-08-19
- Distribution: View Public Website
- Applicable Models
Satellite 100CS Satellite 110CS Satellite 110CT Satellite 200CDS Portege 610CT Portege 650CT Portege 660CDT Tecra 500CDT Tecra 500CS Tecra 510CDT Tecra 530CDT Tecra 700CS Tecra 700CT Tecra 710CDT Tecra 720CDT Tecra 730CDT Tecra 730XCDT Tecra 740CDT Satellite Pro 400CDT Satellite Pro 400CS Satellite Pro 415CS Satellite Pro 425CDS Satellite Pro 430CDS Satellite Pro 430CDT
- Information
- Missing Operating System - Non-system disk or disk error - Boot error Press F1 to retry, NO ROM BASIC, Invalid Media Type - Hard Drive Controller Failure
CAUSE:
Missing Operating System
This error occurs when the boot record signature of the master boot record does not match a certain value at a certain location. In this case, the boot sector is invalid and the computer cannot boot. This error can also occur if there is no active partition defined in the partition table.
Non-System Disk or Disk Error
This error is generated by the computer's BIOS when the boot sector or master boot record of the boot drive is damaged or missing. This error can also occur if the boot device has been improperly configured in the BIOS. In this case, data in the partition may be valid and undamaged, but there is no bootable partition.
NOTE: This message also occurs when a non-bootable disk is left in drive A during startup. If you receive this error, make sure that there is no disk in drive A and restart your computer.
Boot Error Press F1 to Retry
This error is generated by the computer's BIOS when the hard disk is missing a master boot record or boot sector, or when there is a problem accessing the boot drive.
NO ROM BASIC
If there is no active partition defined, the master boot record returns an error to the BIOS. In some cases, the master boot code attempts to go to ROM Basic when no bootable disk is found. Since some computers do not have ROM Basic, they display a NO ROM BASIC or other error message. The message displayed is dependent upon the computer's BIOS.
Invalid Media Type
This error message is displayed when the boot sector of a defined partition is damaged. The error message is normally received using a new partition that has not been formatted. However, if the boot sector is damaged, the partition may appear unformatted to the operating system, and this error message is generated.
Hard Disk Controller Failure
This error message indicates either the hard disk controller has failed, the hard disk controller is not set up properly in the BIOS, or the controller cannot communicate with the attached drive(s). In this case, do not perform the troubleshooting steps below. Instead, consult the documentation included with your computer or contact the computer's manufacturer for more information.
RESOLUTION:
Each of the error messages listed above may indicate problems ranging from improper hardware configuration to damaged hard disk partition information. The following steps can be used to help resolve the problem. However, if these steps do not resolve the problem, please contact your hardware manufacturer or have the drive serviced by a qualified service professional.
1. Start the computer using the Windows 95 emergency boot disk (EBD) or using a bootable MS-DOS disk that contains Fdisk.exe, Format.com, Sys.com, and Scandisk.exe (MS-DOS versions 6.2x only). If your computer does not start from drive A, or if you receive an error message similar to one listed above when you start from drive A, please contact the computer's manufacturer.
2. Use Fdisk.exe to view the partitions on the hard disk by performing the
following steps:
a. Run Fdisk.exe from the EBD or bootable MS-DOS disk.
NOTE: If the hard disk was not partitioned using Fdisk.exe, use the
appropriate third-party partitioning software to view the hard disk
partition(s). For instructions on using the third-party partitioning software, please consult the software's documentation.
b. Select option 4 (Display partition information).
c. If the partitions are listed, make sure that the bootable partition is defined as active (look for an uppercase A in the Status column.)
d. If there are no partitions listed, use Fdisk.exe to establish new partitions and then use Format.com to format the partition you want to boot from.
WARNING: When you use Fdisk.exe or Format.com to create new
partitions or format the drive, you lose any data on that drive or partition.
e. If all the partitions appear in Fdisk.exe, and one is defined as
active, proceed to the next step.
3. Run the SYS command on the hard disk from the EBD or bootable MS-DOS disk. For example, type the following command:
a:\sys c:
If you receive the message "System Transferred," remove the disk from drive A and restart the computer. If you receive the same error message after you restart your computer, your hard disk may be configured improperly or damaged. If you do not receive the "System Transferred" message, or if you receive an error message, run ScanDisk from the EBD or bootable MS-DOS disk (MS-DOS version 6.20 or later) to check for physical damage on the hard disk by typing the following command:
a:\scandisk c:
If you are prompted to perform a surface scan, choose Yes. If ScanDisk reports physical damage on the hard disk, have the hard disk checked by a qualified service professional.
- Export Control and EULA
- Use of any software made available for download from this system constitutes your acceptance of the Export Control Terms and the terms in the Dynabook end-user license agreement both of which you can view before downloading any such software.