The Satellite Pro 440/460/470/480 series models (CDT/CDX) have been tested to be compatible with Microsoft Windows NT 4.0 Workstation and Microsoft Windows NT 4.0 Server. Satellite Pro 440/460/470/480 series computers are qualified under Microsoft "Designed for Windows NT" logo program. For more NT compatibility information, please visit the Microsoft Windows NT Hardware Compatibility List (HCL).

• Satellite Pro notebook computer (440/460/470/480, hereafter referred to as "the computer")
• SelectBay CD-ROM drive
• External floppy disk drive
• AC adapter (if battery is not sufficiently charged)
• Windows NT workstation V4.0 (hereafter refereed to as "NT 4.0")
• CD-ROM (or access to NT 4.0 installation distribution files via network connection)
• Windows NT workstation V4.0 Service Pack 3 (hereafter referred to as "SP3") CD (SP3 can be downloaded, or access to NT SP3 installation files via network connection.)
• NT Support files including Toshiba power management, device driver and utility software for Satellite Pro 440/460/470/480 model computers (Toshiba drivers and utilities software may be downloaded. Please search for relevant model's file section.)

Download the following support files (device drivers and NT utilities) and extract them to blank floppy disks.

If you experience difficulties in transferring Windows NT Utilities or Power Management Utilities to a floppy disk(s), these may be installed after Networking configuration, then download these and extract the utilities directly to the hard disk.(See Network Support Installation below.)

Blank floppy diskettes for creating system bootable disk and NT Emergency Rescue Disk.

1. Memory: 16MB minimum, 32- 64MB preferred
2. Hard Drive: Hard drive formatted with FAT 16 partition.120MB free space minimum, 500MB preferred
3. Setup: TSETUP (Toshiba CMOS setup) must be modified from factory default setting in order to install Windows NT 4.0 correctly.
4. Power on the computer while holding down "ESC" key
5. Press the "F1" key to enter the TSETUP menu.
6. Press the "HOME" key to select default setup
7. Use arrow key to go to "PC card Controller Mode" and change it to "PCIC Compatible"
8. Press the "END" key to save and exit setup.

If you have access to the internal SelectBay CD-ROM at this point, skip this section and go to "Installing Windows NT WorkStation 4.0." Otherwise, you will need to create a CD-ROM boot disk or Network boot disk if NT 4.0 setup files are located on a network server. For local installation via internal SelectBay CD-ROM,

- Create a bootable floppy disk on another computer.

- Copy the necessary CD-ROM drivers (TOSCDROM. SYS, MSCDEX.EXE) onto the bootable floppy disk, then create CONFIG.SYS and AUTOEXEC.BAT files to gain access to the internal CD-ROM. CD-ROM drivers can be found on the Toshiba web site. This example shows how to assign a drive letter Q to the internal CD-ROM.

[Config.Sys]

DEVICE=A:\TOSCDROM. SYS

[Autoexec.Bat]

A:\MSCDEX.EXE /L:Q /D:TOSCD001 /M:10

- Consult your network administrator on how to use a bootable disk to gain access to a file server containing NT 4.0 installation files.

This document will primarily discuss CD-ROM installation.

Toshiba recommends the following installation order:

1. Install Windows NT.
2. Install Service Pack 3.
3. Install PC card network support if needed.
4. Install the video driver.
5. Install the modem driver.
6. Install the sound driver.
7. Reinstall Service Pack 3
8. Install the Toshiba NT APM driver and utilities software.

1. Power up the computer with CD-ROM bootable disk.
2. Insert NT 4.0 installation CD into CD-ROM drive.
3. Copy NT i386 files from NT 4.0 CD to computer hard drive: COPY Q:\I386\*.* C:\I386 (where Q is the CD-ROM drive letter)

Note: It is possible to install NT without copying i386 files to the local hard drive. However, it is recommended to do so in the event that Windows NT does not detect the CD-ROM drive after the computer reboots.

4. Copy SP3 files from SP3 CD to C:\SP3 directory.
5. Go to C:\i386 directory and type in the following command to install NT. C:\i386\WINNT /B

Note: WINNT /B will perform a floppy-less installation. If boot floppies need to be made, the "WINNT /OX" command will generate NT installation disk sets (3 disks) and can be used to boot up the computer from the floppy drive.

6. When prompted for path to NT installation files, enter "C:\i386" and press the "ENTER" key to continue. Please be patient while installation process copies files.
7. When prompted that MS-DOS portion setup is completed, press the "ENTER" key to restart.
8. At the Welcome to setup screen, press the "ENTER" key to continue.
9. Press the "ENTER" key to accept the "IDE CD-ROM (ATAPI 1.2)/PCI IDE controller" selection.
10. When prompted with the Windows licensing agreement, press the "PgDn" key to scroll down and press F8 to continue.
11. Press "ENTER" to continue after default hardware and software components setup menu.
12. Press "ENTER" to continue installing NT on drive C, or choose a different drive letter to install.
13. Presses "ENTER" to leave file system intact (FAT 16) or choose to convert to NTFS.

Note: Toshiba recommends using FAT16 for the initial installation, then converting to NTFS. For a detailed discussion of FAT, HPFS and NTFS file systems, please refer to the "MS Windows NT Resource Guide" within the "MS Windows NT Resource Kit." Refer specifically to Chapter 5 "Windows NT File Systems and Advanced Disk Management."

14. Press "ENTER" to continue installing NT in \WINNT directory or type in a different directory name to install.
15. Press "ENTER" to allow NT to examine the hard drive for corruption.
16. When prompted to reboot, press "ENTER" to continue.
17. At Windows NT setup GUI (Graphic User Interface) screen , click "NEXT" to continue.
18. Select "TYPICAL" setup option, click "NEXT" to continue.
19. Enter Username and Organization name, click "NEXT" to continue.
20. Enter the 20 digit Product ID number found on the NT CD package, click "NEXT" to continue.
21. Enter a unique computer name and click "NEXT" to continue.

Note: A computer name should be unique so that other computers on the network can identify it, for example: "440SP-NT4."

22. Enter the Administrator password twice, click "NEXT" to continue.
23. Select "Create an Emergency repair disk," click "NEXT" to continue.
24. Select "Install the most common component," click NEXT" to continue.
25. Press "NEXT" to continue installing NT networking.
26. Select "Do not connect this computer to a network at this time," click "NEXT" to continue.

Note: Toshiba recommends installing NT networking support after NT has been fully installed. To install networking at this point may interrupt the rest of installation process.

27. Press "NEXT" to finish setup.
28. Select appropriate time zone, click "CLOSE" to continue.
29. Click "OK" twice to accept VGA-Compatible Display Adapter (the video driver will be installed later).
30. Insert a blank floppy diskette when prompted then press the "ENTER" key to continue.
31. When finished, remove the floppy disk and label it as "Satellite Pro 440 Emergency Rescue Disk."
32. Press the "ENTER" key to restart the computer.

When booting NT for the first time, the following menu is shown after POST (Power On Self Test).

1. Boot into Windows NT.
2. Open Windows NT explorer.
3. Go to SP3 directory and double click "UPDATE.EXE" to install.

Follow screen instructions to finish installing SP3.

1. Boot into Windows NT.
2. Go to Control Panel, double click NETWORK icon.
3. Click "YES" to begin network installation.
4. Click "NEXT" to install wired network. (Use Remote Access if applicable)
5. Click "SELECT FROM LIST" to continue.
6. Select the correct network adapter from list. If exact network adapter is not found, click "HAVE DISK." Enter proper path to the network driver files. (For example: A:\)
7. Select the proper network adapter type and click "NEXT" to continue.
8. Select all applicable network protocols and click "NEXT" to continue.
9. Click "NEXT" to continue installing network services.
10. Click "NEXT" to install selected network components.
11. When prompted for Windows NT files, enter "C:\i386" in the path.
12. Click "CONTINUE" to accept I/O address and Interrupt values.
13. Select applicable network type (PCMCIA, ISA or PCI) and "0" for network number. Click "OK" to continue.
14. Click "OK" again to confirm using current netcard parameters.
15. Click "OK" to use DHCP or "NO" to specify TCP/IP configuration for non-DHCP settings.
16. Enter correct IP, DNS, WINS settings and click "OK" to continue.
17. Click "NEXT" twice to start the network.
18. Enter correct Workgroup and Domain information, click "NEXT" to continue.
19. Click "FINISH" to restart the computer. Note: You may setup Internet access at this point to download the remaining drivers and utilities directly to your hard disk.

1. Boot into Windows NT.
2. Go to Control Panel. Double click "DISPLAY" icon.
3. Choose "Setting," click "DISPLAY TYPE."
4. Enter the correct path for the video driver files and click "OK" to continue.
5. Choose "Chips Video Accelerator (64300/10 65535/40/45/48/50/54/55)" and click "OK" to continue.
6. Click "YES" to proceed.
7. Click "OK" to accept that driver has been installed correctly.
8. Click "CLOSE" to close display type dialog box window.
9. Click "CLOSE" to close display properties dialog box window.
10. Click "YES" to restart Windows NT. (The new display driver will not take effect until the system is rebooted)

Choose proper video resolution and number of colors after NT reboots.

1. Boot into Windows NT.
2. Go to Control Panel. Double click "PORTS."
3. Click "ADD."
4. Make sure to select COM port =2, Base I/O Address = 02F8, IRQ = 3. Click OK to continue.
5. Click "DON'T RESTART NOW" to continue setup.
6. Click "CLOSE" to close Port setting dialog box.
7. Go to Control Panel. Double click "MODEM."
8. Check box "Don't detect my modem .." and click "NEXT" to continue.
9. Select "Standard 28800 bps modem." Click "NEXT" to continue.
10. Select "SELECTED PORTS" and "COM2." Click "NEXT" to continue.
11. Enter location information. Click "NEXT" to continue.
12. Click "FINISH," then "CLOSE" to end the setup.

Modem will function after restarting the computer.

1. Boot into Windows NT.
2. Go to Control Panel. Double click "MULTIMEDIA" icon.
3. Click "DEVICES."
4. Click "ADD."
5. Select "UNLISTED OR UPDATED DRIVER" and click "OK" to continue.
6. Enter the correct path for sound driver files and click "OK" to continue.
7. Select "OPL3SA Sound system [English]" and click "OK" to continue.
8. Click "OK" to confirm sound card hardware setup.

Click "RESTART NOW" to restart the computer.

1. Boot into Windows NT.
2. Open Windows NT explorer.
3. Go to SP3 directory and double click "UPDATE.EXE" to install.

Follow screen instructions to finish installing SP3.

1. Boot into Windows NT.
2. Double click Toshiba power management and utility program to begin installation (i.e. 440-nt4.exe or other file name listed for the your model)
3. Click "SETUP" button to continue setup.
4. Review HTML based help file and close it. Answer "Y" to continue installation.
5. Click "OK" when completed successfully.
6. Press "ENTER" to install the SCI driver.
7. Click "CONTINUE" to confirm installing SCI driver. Click "OK" when finished.
8. Click "ENTER" to install Windows NT utilities.
9. Click "OK" to accept \WINUTILS as target directory.
10. Click "CONTINUE."

Review HTML based help file and close it. Shutdown and restart Windows.

The following MultiMedia and Video Enhancements are NOT supported under NT 4.0:

• DVD movies
• MPEG2 playback
• VideoBrush
• RingCentral Telephony Applications
• USB

Please check the Toshiba Technical Service and Support web site for updated drivers, utilities and other configuration information.